You need one uncut sheet of printer paper, short edge at the top. No scissors, tape or clips. Measurements are rounded to the nearest ⅛ inch, as in the app.

moves fold line where it lands Diagrams are drawn on Letter and zoom in after the fold in half; the bar in each corner is 1 inch. Tap a diagram to watch the fold.

Fold it step by step

01
Crease down the middle
Fold the sheet in half the long way, press, and open it.
This is your guide line.
02
Fold the top edge down
Fold the top edge down ⅞ in (2.2 cm). Keep it straight across.Fold the top edge down 2.4 cm (⅞ in). Keep it straight across.
Line it up with the sides of the page.
03
Roll it again
Fold that strip down once more, the same width.
The rolled strip stacks layers along the front edge.
04
Fold the top corners in
Fold the top-right corner down so the rolled edge lies along the center crease.
Fold right over the strip. It is thick, so press firmly.
05
And the left corner
Same on the left side.
The two edges meet on the crease.
06
Fold it in half
Fold in half along the crease with the flaps inside.
Press from nose to tail.
07
Fold down the first wing
Fold the top layer down on a slant: 3 in (7.6 cm) from the center fold at the nose, ½ in (1.3 cm) from it at the tail.Fold the top layer down on a slant: 7.6 cm (3 in) from the center fold at the nose, 1.3 cm (½ in) from it at the tail.
The crease slants: farther from the center fold at the nose than at the tail. Measure both ends.
08
Fold the wingtip back
Fold the tip of this wing back over, ⅝ in (1.5 cm) in from its edge.Fold the tip of this wing back over, 1.5 cm (⅝ in) in from its edge.
This becomes a winglet.
09
Turn it over
Flip the plane over.
Nose pointing away.
10
Fold down the second wing
Fold this wing down on the same slant as the first one.
Compare the wings: an unequal pair is the usual cause of a turn.
11
Fold the other tip back
Fold this wingtip back the same amount.
Both winglets the same size.
12
Open the wings and bend the tips down
Open the wings into a clear Y, then bend both wingtips straight down.

Check the shape

From behind: this is the view to compare with your plane.

Compare the droop on both sides from the front. Test changes in small increments rather than flattening one tip and leaving the other untouched.

Before you open the wings, hold the plane closed against a window: both wing outlines should cover each other. Fix an unequal wing crease before reaching for trim.

First flights

Launch: Hold it near the middle and let it go gently, nose just above level.

Rolled edge. The rolled strip is the stiff front of the wing. If it starts to unroll at one end, re-press it; a loose roll changes one wing more than the other.
Drooped tips. The tips bend down on purpose. Compare them from the front and keep the droop equal; do not flatten one to fix a turn.

If it misbehaves

Dives straight down: Release level, then bend both back edges up a hair.
Climbs, then drops: Flatten those bends a little; throw nearer level.
Always turns one way: Compare the wings first. Then bend the edge on the inside of the turn down, or the outside edge up, very slightly.

Full troubleshooting guide →

The app can fly this plane in a simulator. Its distances and paths are simulation output; this page makes no claim about how far a hand-folded Gull will fly.

More rolled leading edges

Instead of a point, the top edge is rolled down two or three times into a stiff strip. The wings stay broad, and the rolled edge becomes the front of each wing.